Demand-Controlled Ventilation (DCV) in Commercial Buildings: A Practical Engineering Guide

BMS-Based Dynamic Closed-Loop Control with Multi-Parameter Indoor Air Quality Monitoring, Equipment Selection, and Communication Protocols

Demand-Controlled Ventilation | Multi-Parameter IAQ Monitoring | BMS Integration | MQTT / BACnet / Modbus | RESET / WELL / LEED

1. Why Commercial Buildings Need Demand-Controlled Ventilation

WHY DCV

Heating, ventilation, and air conditioning (HVAC) systems typically account for 30%–45% of total energy consumption in commercial buildings. Conventional Constant Air Volume (CAV) systems are generally designed to deliver ventilation based on maximum occupancy, regardless of how many people are actually present.

While this approach provides a straightforward ventilation strategy, it creates two major challenges: unnecessary energy consumption and limited visibility into indoor air quality.

Excessive Outdoor Air Increases Heating and Cooling Loads

Traditional ventilation systems maintain a relatively constant outdoor airflow based on peak occupancy requirements. During off-peak hours, early mornings, evenings, or periods when meeting rooms are unoccupied, large volumes of outdoor air may still need to be heated or cooled.

This unnecessary conditioning significantly increases HVAC energy consumption without delivering proportional benefits to building occupants.

Single-Parameter Control Creates Indoor Air Quality Blind Spots

Ventilation strategies based exclusively on carbon dioxide (CO₂) measurements cannot provide a complete picture of indoor environmental conditions.

Although CO₂ is a useful indicator of occupancy-related ventilation demand, it cannot detect volatile organic compounds (TVOCs) released by carpets and furniture or fine particulate matter (PM2.5) entering buildings during outdoor pollution events.

Consequently, CO₂-only ventilation control may not adequately meet the broader indoor air quality requirements of advanced green building standards.

DCV Enables Intelligent, Closed-Loop Ventilation Control

Demand-Controlled Ventilation (DCV) addresses these challenges by connecting real-time indoor air quality monitoring with Building Management Systems (BMS).

Multi-parameter IAQ monitors can be installed in return-air ducts, at Variable Air Volume (VAV) terminals, and in representative occupied breathing zones.

Real-time environmental measurements are transmitted to the BMS, allowing ventilation dampers and variable-speed fans to respond dynamically to changing indoor conditions.

The result is a more responsive ventilation strategy that delivers outdoor air according to actual demand, helping balance energy efficiency with occupant health and comfort.

2. Selecting the Right Tongdy IAQ Monitoring Solutions

PRODUCT SELECTION

Air quality sensors serve as the essential sensing layer of a DCV closed-loop control system. Their measurement capabilities, installation locations, and communication interfaces directly influence the performance and reliability of ventilation control.

With more than 18 years of industry experience and a portfolio of over 200 monitoring products, Tongdy provides commercial-grade environmental monitoring solutions for occupied indoor spaces, HVAC ductwork, and outdoor environments.

Different building applications require different monitoring configurations.

MSD and PGX — Advanced Multi-Parameter IAQ Monitoring

Key Monitoring Capabilities

PM2.5 and PM10 particulate matter

Carbon dioxide (CO₂)

Total volatile organic compounds (TVOC)

Temperature and relative humidity

Optional formaldehyde (HCHO) and carbon monoxide (CO) monitoring

Communication Interfaces and Protocols

Depending on model and configuration, supported communication options include RS-485, Ethernet, Wi-Fi, LoRaWAN, and 4G, together with Modbus RTU, BACnet MS/TP, MQTT, and HTTP.

The product selection described in this guide also highlights RESET Air Grade B certification.

Typical Applications

Commercial office buildings, shopping malls, banks, airports, exhibition centers, and other large occupied commercial environments.

These monitors provide comprehensive environmental measurements that can support building automation, indoor air quality management, and continuous performance assessment.

TSP-18 and EM21 — Indoor Environmental Monitoring

Key Monitoring Capabilities

These monitoring solutions combine NDIR infrared CO₂ measurement with temperature, relative humidity, TVOC, and particulate matter monitoring.

Optional environmental parameters include ambient light and noise levels.

Typical Applications

Hotels, school classrooms, libraries, technology and innovation parks, and smaller public spaces.

They are particularly suitable for applications requiring ongoing environmental monitoring and occupancy-sensitive ventilation management.

PMD Series — Duct-Mounted Air Quality Monitoring

Key Technical Features

The PMD series is designed for installation within HVAC duct systems.

Its dedicated air-sampling and airflow-guidance structure separates the sensing compartment from the control compartment, helping accommodate demanding duct conditions.

Optional monitoring parameters include ozone and carbon monoxide, with configurations designed for high air velocities and elevated humidity.

Typical Applications

  • Main return-air ducts of Air Handling Units (AHUs)
  • Outdoor air intake systems
  • Central ventilation equipment
  • Monitoring applications involving filtration performance and differential pressure across filter sections

Duct-mounted monitors provide centralized environmental information that complements measurements collected directly from occupied spaces.

MyTongdy — IoT Monitoring and Data Management Platform

MyTongdy is Tongdy's proprietary IoT-based environmental monitoring platform.

It supports centralized data management across multiple monitoring devices and building projects.

Its key capabilities include:

  • Multi-device environmental data collection and storage
  • Real-time and historical trend visualization
  • Remote device monitoring and diagnostics
  • Remote calibration and maintenance support
  • Historical data retrieval and download
  • Cross-project environmental performance analysis

By collecting and organizing monitoring data from different buildings, MyTongdy helps facility managers evaluate long-term environmental performance and provides continuous data records for green building certification and operational reporting.

3. Three-Stage Dynamic Closed-Loop BMS Control Strategy

CLOSED-LOOP CONTROL

A practical DCV system should adjust ventilation based on measured indoor environmental conditions rather than fixed airflow schedules.

The following three-stage strategy illustrates how CO₂ measurements and odor conditions can be used as control references to coordinate ventilation dampers and variable-speed fans through the BMS.

Stage 1 — Energy-Saving Baseline

CO₂ ≤ 650 ppm

When indoor CO₂ concentrations remain at or below 650 ppm, the ventilation system operates in its energy-saving baseline mode.

The system maintains the designed minimum outdoor airflow, typically around 20%–30%, while preserving indoor positive pressure within approximately 5–10 Pa.

Ventilation continues at a level intended to satisfy baseline requirements without unnecessarily increasing heating or cooling loads.

Primary Objective: Minimize unnecessary HVAC energy consumption while maintaining essential ventilation and indoor pressure conditions.

Stage 2 — Dynamic Ventilation Adjustment

CO₂: 650–900 ppm

As indoor CO₂ concentrations rise, indicating increasing occupancy-related ventilation demand, the BMS activates dynamic ventilation control.

A Proportional-Integral-Derivative (PID) control strategy adjusts the opening of VAV dampers and regulates variable-frequency fans according to changing environmental measurements.

Outdoor airflow increases progressively as ventilation demand rises.

Rather than operating continuously at maximum capacity, the ventilation system adapts to actual conditions within occupied areas.

Primary Objective: Match ventilation supply to changing demand while avoiding unnecessary energy consumption.

Stage 3 — Enhanced Air Purging

CO₂ > 900 ppm or Odor Detected

When the indoor CO₂ concentration exceeds 900 ppm or an odor is detected, the BMS activates enhanced ventilation mode.

Outdoor air dampers are fully opened, and exhaust fans are activated to accelerate air exchange and remove accumulated indoor pollutants.

The system maintains enhanced ventilation until indoor environmental conditions return to the required control range, after which normal ventilation operation can resume.

Primary Objective: Respond promptly to elevated CO₂ concentrations or detected odors, accelerate air exchange, and restore acceptable indoor air quality conditions.

Maintaining Positive Building Pressure

Energy-saving ventilation control must not compromise the building's pressure-management requirements.

The BMS should establish a mandatory minimum outdoor airflow baseline, generally around 15%–25% of the design airflow in the example described here.

Supply and exhaust fan speeds should be coordinated through variable-frequency control to maintain approximately 5–10 Pa of positive indoor pressure continuously, 24 hours a day, where required by the building's pressure-control strategy.

This pressure differential helps reduce uncontrolled infiltration of outdoor particulate matter and unconditioned humid or hot air through building envelope gaps.

By coordinating minimum ventilation requirements with exhaust airflow, the system can balance indoor air quality, pressure stability, and HVAC energy efficiency.

4. Frequently Asked Technical Questions

FAQ

Q1. How can building operators prevent long-term sensor baseline drift from triggering incorrect BMS control actions?

Tongdy's NDIR CO₂ sensors incorporate Automatic Baseline Calibration (ABC) technology to help maintain measurement stability over extended operating periods. The sensors are designed for a service life of up to 15 years.

However, continuous 24-hour operation may not always provide the environmental conditions needed for conventional automatic baseline calibration.

For such applications, as well as monitoring systems using TVOC, particulate matter, and other electrochemical sensors, the MyTongdy platform supports remote data diagnostics and calibration functions.

These capabilities help reduce the need for technicians to access, remove, and manually service individual monitoring devices.

Q2. How can a DCV system reduce energy consumption while maintaining positive indoor building pressure?

The key is to establish a mandatory minimum outdoor airflow requirement that the DCV system cannot reduce below.

A typical example is a minimum airflow baseline of approximately 15%–25% of the design ventilation rate, combined with coordinated variable-speed exhaust fan operation.

This approach allows the system to adjust ventilation according to demand while maintaining an indoor positive pressure of approximately 5–10 Pa continuously, 24 hours a day.

Proper pressure control helps prevent outdoor particles, moisture, and unconditioned air from entering the building through uncontrolled leakage paths.

Q3. How can Tongdy monitoring devices integrate with BMS platforms from Johnson Controls, Siemens, or Honeywell?

Tongdy's commercial monitoring portfolio provides standard building automation communication options.

These include RS-485 interfaces using Modbus RTU and BACnet MS/TP, as well as Ethernet-based communication options such as Modbus TCP, BACnet IP, and MQTT.

Standardized register maps and BACnet object definitions help simplify system integration.

With the appropriate device configuration and compatible BMS interfaces, monitoring data can be incorporated into existing building automation networks without the need for complicated custom gateways.

This enables real-time environmental information to become part of the building's ventilation and energy-management strategy.

Q4. Can continuous air quality monitoring data support LEED, WELL, and RESET green building certifications?

Yes. Continuous environmental monitoring can provide valuable supporting data for green building certification, performance verification, and ongoing operational assessment.

Tongdy is a Gold Action Supporter of the World Green Building Council's (WGBC) global monitoring initiative, and multiple Tongdy air quality monitoring product series have obtained RESET Air Grade B certification.

Continuous monitoring records can support environmental compliance documentation associated with LEED v4.1, WELL v2, and relevant RESET requirements.

By establishing a reliable monitoring infrastructure, building operators can use the same environmental data network to support multiple sustainability and indoor environmental quality objectives, subject to the requirements of each certification program.

Q5. How should duct-mounted air quality monitors and wall-mounted indoor monitors work together within a DCV system?

Both types of monitoring equipment perform complementary functions.

Wall-mounted indoor monitors, such as MSD and TSP devices, measure environmental conditions directly within occupied breathing zones.

Their measurements support localized ventilation adjustments and more precise environmental management in individual rooms or building zones.

Duct-mounted monitors measure air quality within central HVAC systems, including main AHU return-air ducts and outdoor air intake sections.

These measurements support centralized ventilation management, supply-air assessment, and filtration-related monitoring.

Combining the two creates a dual-level monitoring and control structure:

  • Centralized control: Duct-mounted monitoring provides information for overall ventilation system management.
  • Zone-level control: Indoor monitors provide localized measurements for individual occupied spaces.

Together, they enable a coordinated approach that connects building-wide ventilation operation with the actual environmental conditions experienced by occupants.

Q6. What operational benefits does MyTongdy provide for property and facility managers?

MyTongdy enables centralized monitoring and management of environmental data across multiple buildings, projects, and geographic locations.

The platform supports flexible deployment through gateways, local computers, servers, and cloud-based configurations.

Environmental information can be viewed through devices such as smartphones, PCs, and large display screens.

Its functions include real-time environmental trend analysis, historical data downloads, comparisons between devices, remote diagnostics, calibration support, and alerts when monitored parameters exceed configured limits.

By consolidating environmental monitoring into a centralized platform, MyTongdy helps facility managers reduce routine on-site inspections, improve maintenance efficiency, and simplify environmental performance reporting and energy audits.

Q7. What are some representative Tongdy air quality monitoring projects?

Tongdy's monitoring solutions have been deployed in more than 300 projects worldwide, supporting commercial buildings and other demanding indoor environments.

Representative applications include:

  • ByteDance office developments, China: Indoor environmental monitoring across commercial office environments.
  • One Raffles Quay, Singapore: Air quality monitoring within a major twin-tower commercial office complex.
  • One Bangkok, Thailand: Environmental monitoring applications in a large commercial development.
  • Rockefeller Plaza, United States: Monitoring applications associated with a prominent commercial property.

These projects demonstrate the practical application of continuous environmental monitoring in commercial real estate and building operations.

Long-term deployments also provide valuable experience in equipment reliability, environmental performance assessment, and integration with building management systems.

5. Building a Smarter and Healthier Ventilation System

Demand-Controlled Ventilation is not simply a method of reducing outdoor airflow. It is a coordinated engineering approach that brings together environmental sensing, automated control, and continuous operational management.

By combining multi-parameter IAQ monitoring with BMS-based dynamic ventilation strategies, commercial buildings can respond more effectively to changing occupancy patterns and indoor environmental conditions.

Tongdy's commercial monitoring solutions provide the sensing infrastructure needed to support this approach, from individual occupied rooms to centralized HVAC duct systems.

When properly designed, commissioned, and operated, this integrated strategy can help deliver:

  •  More efficient HVAC operation and reduced unnecessary heating and cooling loads
  •  Continuous visibility into indoor air quality conditions
  • Adaptive ventilation responses to changing environmental demand
  • Improved coordination between centralized and zone-level ventilation control
  • Long-term monitoring data for facility management and green building performance assessment

Tongdy Commercial IAQ Monitoring + BMS-Based Demand-Controlled Ventilation

= Potential HVAC Energy Savings of 20% or More + Long-Term Indoor Air Quality Management

Actual energy savings depend on building design, occupancy patterns, control settings, climate conditions, and system operation.

Beijing Tongdy Sensing Technology Corporation

Advancing Healthier Buildings Through Environmental Monitoring and Control Technologies.

200+ Monitoring Products | Trusted by 100+ Multinational Companies | 300+ Reference Projects | Presence in 30+ Countries and Regions


Post time: Nov-19-2026